Art-Net Menu

Art-Net is a royalty-free protocol developed by Artistic Licence (http://www.artisticlicence.com).

grandMA3 supports Art-Net 4.

It is configured in the Art-Net menu:

See the Ethernet DMX topic for information on how to open this menu.

See the Transmit DMX using Art-Net topic for an explanation of the steps needed to transmit Art-Net.

Config Buttons

There are some buttons at the top of the menu:

• Preferred IP:
  This is the preferred IP address or address range used by the Art-Net protocol. The Interface can be set to Auto allowing this setting to select the interface that matches the preferred setting. Tap this input button to open a small number input pop-up. The preferred number has to be input as an IP address with the subnet mask written in CIDR notation. For instance, 10.0.0.0/8 tells the system that it prefers an IP address that starts with 10. The rest of the numbers do not matter (the "/8" is the same as subnet mask 255.0.0.0).
• Interface:
  Tap this button to open the Select Interface pop-up where the desired network interface can be selected. This interface will be used for all Art-Net in and out. The Auto option can be used to allow the Preferred IP setting to select the interface. The interface is written inside "<" and ">" when it is selected by the preferred setting.
• Enable Output:
  This On/Off button needs to be On for the master to transmit Art-Net. Data also needs to configured for output - read more below.
• Enable Input:
  This On/Off button needs to be On for the master to receive Art-Net. Data also needs to configured for input - read more below.
• Broadcast Threshold:
  This input button sets the amount of Art-Net receivers for a universe before the master starts to send the universe as broadcast. This is only valid if the mode is set to Auto. If the amount of receivers is below the threshold, then the universe is sent as Unicast. If it is above, then the universe is sent as Broadcast.
• ArtPollRate:
  This input sets the time between each ArtPollRequest packet sent by the master station.
• Setup:
  This On/Off button is used to toggle the setup mode. This mode can be used to transmit and receive configuration data only. If the output and input are turned Off then only the configuration data transmitted and received.

There are two tabs below the buttons. They are Data and Nodes. Data is used to setup output and input. Nodes can be used to see the discovered nodes in the network. If the nodes support it, then this can also be used to configures the ports on the node.

Data Tab

The data tab is a grid of rows and columns. Each row is an Art-Net configuration. If the row is not valid or not enabled, then the name is in red text.

This is a short description of the columns:

• Lock:
  The row can be locked to prevent changes.
• No:
  This is the row number.
• Name:
  Each row can have a name. This can be used as short info for the row.
• Enabled:
  This Yes or No field is used to enable the row transmitting or receiving Art-Net. Yes is the default.
• Mode:
  The mode defines what the row is doing. There are four options:
  • Broadcast:
    This transmits Art-Net using broadcast.
  • Unicast:
    This transmits Art-Net using unicast.
  • Auto:
    This transmits Art-Net. It uses the Broadcast Threshold number to determine if universes should be transmitted using broadcast or unicast. If the number of universe subscribers (determined by ArtPollRequests) are below the threshold, then it is sent using unicast. Is it above the threshold, then it is broadcasted.
  • Input:
    The row is receiving Art-Net and merging it into the defined universe.
• Destination IP:
  This field is only active if the unicast mode is selected. This is the IPv4 address of the receiving device.
• Subscribed Nodes:
  This field is information about the amount of subscribing devices. This is determined using ArtPollRequests.
• Local Universe:
  This is the grandMA3 universe to be transmitted or the universe that should receive incoming Art-Net DMX. If the amount is more than one, then this is the first universe in the range.
• Amount:
  This is the amount of grandMA3 universes to be transmitted or received.
• Net:
  The net number is a value 0 and 127. There are 128 different nets since Art-Net III. Each net is a complete group of Sub-Nets and Universes. This allows for addressing a total of 32 768 Art-Net universes. To be compatible with Art-Net I and Art-Net II devices, please use net 0.
• Art-Net Sub-Net:
  There are 16 sub-nets in Art-Net. They can be input in decimal numbers from 0 to 15 or 0 to F in hex numbers.
• Universe:
  There are 16 universes in each sub-net. They can be input in decimal numbers from 0 to 15 or 0 to F in hex numbers.
• Art-Net Absolute:
  This is the absolute universe number. It is calculated based on the net, sub-net, and universe numbers. It can also work the other way. A universe number can be input here and then the net, sub-net, and universe numbers are calculated based on the input.
• Delay:
  A delay can be set up between each transmitted universe. This can be helpful for older nodes with slower network cards. Sending many universes at once can flood the node. Adding a small delay helps. This setting is only available for outputting modes.
• Input Priority:
  This priority is the priority the received Art-Net packets are merged into the grandMA3 universe. This is no specific Art-Net setting. This is the same priority for normal DMX input and playbacks. This can only be changed when the mode is input.
• Timecode Slot:
  Any received ArtTimeCode is sent to the timecode slot number defined here. The mode does not need to be set to Input to receive the timecode, but Input needs to be enabled. This setting can only be changed when the mode is input. There are a total of 8 timecode slots. Read more about them in the What are timecode slots topic.

 

Nodes Tab

Each node detected is a row. Each node has one or more sub rows with "binds". Each bind can only have 4 ports. If a device has more than 4 ports then the device has multiple binds.

• Lock:
  The row can be locked to prevent changes.
• No:
  This is the row number.
• Name:
  Each row gets a name from the device. The name can be edited if the device supports it.
• IP:
  The IP address of the device. The address can be edited if the device supports it.
• Art-Net Network:
  Each bind has a net number. The number can be edited if the device supports it.
• Art-Net Sub-Network:
  Each bind has a sub-net number. The number can be edited if the device supports it.
• Output Port:
  This is the universe number of output ports on the device. The number can be edited if the device supports it.
• Input Port:
  This is the universe number of input ports on the device. The number can be edited if the device supports it.