• MA Network Switch
    • Introduction
      • Intended Use
      • Dangers caused by Electric Current
      • General Safety Instructions
      • System Requirements
      • SFP Transceiver Compatibility
    • Device Overview
      • Front Panel
      • Rear Panel
      • LED Indicators
      • Factory Defaults
    • First Steps
      • Unpack the Device
      • Install Mini-GBIC (SFP)
      • Installation in a Rack
      • Connect the Hardware
      • Set the IP Address on the PC
      • Access the Web Interface
    • Display Navigation
      • Groups View
      • Name View
      • Workload View
      • LAG View
      • Reset View
    • Ports / Groups
      • Change Port Description
      • Assign Groups to Ports
      • Edit LAGs
      • Edit RSTP
      • Edit Speed Setting
      • Change Group Name
      • Edit IGMP Snooping
      • Edit IGMP Querier
      • Edit Unknown Flooding
      • Change VLAN ID
    • Presets / Filters
      • Assign Presets to Ports
      • Apply Filters to Ports
      • Create New Presets
      • Update Presets
      • Create New Filter
      • View Filters
      • Delete Presets
      • Delete Filter
    • General Settings
      • Change Name
      • Change ID
      • Change DHCP Client
      • Change IP Address
      • Change Subnet Mask
      • Change Default Gateway
      • Change SNMP Status
      • Change Password
      • Update Firmware
      • Fallback to Backup Firmware
      • Get Switch Configuration
      • Edit Port Mirroring
      • Upload Switch Configuration
      • Reset Settings
      • Web Interface and grandMA2
    • Specifications
    • Support
    • Glossary
Select different version
 
Hint:
New help version
The help version you selected belongs to an older software version. You may want to view the latest help version.
Version 3.8

Presets / Filters

Table of contents of this topic

This chapter provides information about the preset and filter options provided trough the web interface.

What are presets?

It is useful to apply presets or filters to ports for a higher network performance or for safety reasons, e.g. to block Telnet.

A preset contains collection of filters.

Presets are used to allow or to block the protocol you have selected.

If a preset is set to allow (= green), the network packets matching the filters in the preset are allowed. All other network packets not matching the filters of this preset, will be blocked.
If a preset is set to block (= red), the network packets matching the filters in the presets are blocked. All other network packets not matching the filters of this preset, will be allowed.

Important:
Filters are applied in the outbound and the inbound network traffic of the specific physical connector.

There are seven predefined presets available:

  • MA-Net2
  • dot2-Net
  • Art-Net
  • MA-Remote
  • MA-Net1
  • grandMA2
  • sACN
Important:
Use presets only if a filter function is required. If you use the MA Network Switch in a MA System it is not mandatory to use the grandMA2 preset.

For more information, see apply presets.

For more information about the predefined presets, see factory defaults.

What are filters?

Instead of using presets, you can use filters. For more information, see apply filters.

Filters are objects consisting of:

  • data type
  • addressing
  • further parameters depending on the data type

There are 43 predefined filters available. To get an overview about the predefined filters, go to the extended mode in the web interface. For more information about the predefined filters, see factory defaults.

If you are a network configuration expert, you can create new presets and new filters. For more information, see create new preset and create new filter.

The following table displays the always forwarded filters to provide basic network functionality. These filter cannot be blocked.

Filter Frame Match
IPMCv6 IPv6 next-header 58
IPMCv4 IPv4 protocol nr 1 (ICMP)
IGMP IPv4 protocol nr 2 (IGMP)
DHCP client IPv4 UDP port 68
DHCP IPv4 UDP port 67
ARP arp

 




Sub topics

Select different version