• MA Network Switch
    • Introduction
      • Intended Use
      • Dangers caused by Electric Current
      • General Safety Instructions
      • System Requirements
      • SFP Transceiver Compatibility
    • Device Overview
      • Front Panel
      • Rear Panel
      • LED Indicators
      • Factory Defaults
    • First Steps
      • Unpack the Device
      • Install Mini-GBIC (SFP)
      • Installation in a Rack
      • Connect the Hardware
      • Set the IP Address on the PC
      • Access the Web Interface
    • Display Navigation
      • Groups View
      • Name View
      • Workload View
      • LAG View
      • Reset View
    • Ports / Groups
      • Change Port Description
      • Assign Groups to Ports
      • Edit LAGs
      • Edit RSTP
      • Edit Speed Setting
      • Change Group Name
      • Edit IGMP Snooping
      • Edit IGMP Querier
      • Edit Unknown Flooding
      • Change VLAN ID
    • Presets / Filters
      • Assign Presets to Ports
      • Apply Filters to Ports
      • Create New Presets
      • Update Presets
      • Create New Filter
      • View Filters
      • Delete Presets
      • Delete Filter
    • General Settings
      • Change Name
      • Change ID
      • Change DHCP Client
      • Change IP Address
      • Change Subnet Mask
      • Change Default Gateway
      • Change Password
      • Update Firmware
      • Fallback to Backup Firmware
      • Get Switch Configuration
      • Edit Port Mirroring
      • Upload Switch Configuration
      • Reset Settings
      • Web Interface and grandMA2
    • Specifications
    • Support
    • Glossary
Select different version
 
Hint:
New help version
The help version you selected belongs to an older software version. You may want to view the latest help version.
Version 3.3

Specifications

Table of contents of this topic

hide

Connectivity

Network

9 x 10/100/1000 Mbps shielded Neutrik etherCON connectors
1 on the front, 8 on the rear

4 SFP cages (mini-GBIC)
2 on the rear, 2 inside the MA Network Switch
Power 1 x Neutrik powerCON In

 

Switch Features

Rapid Spanning Tree Protocol (RSTP) Yes
Groups (=VLANs) Yes
Link Aggregation (LAG) Yes
Port mirroring Yes
Fan 2
Ethernet Compliance IEEE 802.1Q VLAN
IEEE 802.1w Rapid Spanning Tree Protocol
IEEE 802.3, IEEE 802.3i,
IEEE 802.3u, IEEE 802.3z
IEEE 802.3x Flow Control,
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3ad Link Aggregation
Supported Protocols

MA-Net2, MA-Net, sACN, Art-Net, and many more.
IEEE 802.1p CoS (Class of Service)
DiffServ (DSCP)
IEEE 1588 PTP V2
Sound Protocol Compliance Yes, Low jitter
Ethernet Switch Type Full non blocking wire-speed switching performance
Memory 4Mb
MAC Address Table 8912 Entries
Address Learning / Aging Self learning, Auto aging
Switching Throughput 32Gbps
IGMP Support Yes
IGMP Snooping

Yes

 

Port Features 

Port Sensing Auto negotiation
Auto Crossover MDI / MDIX (allow to use straight or cross wired cable)
Auto Sensing Full or Half Duplex (Gigabit is Full Duplex)

 

Status Reports 

Front End Display Yes
Ethernet Port Connection Link, Group
Ethernet Port Speed 100/1000Mbps LED
Device Status LED (Green/Red)
Power Status LED (Green/Red)

 

Management 

Configuration Via the web interface.

 

Power Input

Power Input

100 - 240VAC
50 - 60Hz
Power Consumption Maximum 1A

 

Environmental 

Operating Temperature 0 °C to +45 °C
32 °F to 113 °F
Storage Temperature

-10 °C to +60 °C

14 °F to 140 °F
Humidity (non condensing) 20 % to 80 % relative humidity

 

Physical 

Enclosure Metal housing
Dimensions (W x D x H) 483 x 233 x 43 mm
19" x 9.17" x 1.69"
Weight without optical fiber connector

3.5 kg

7.7 pounds
Weight with optical fiber connector

3.7 kg

8.2 pounds

 

Approvals 

CE Yes
EN 55103-1 Yes
EN 55103-2 Yes
EN 60950-1 Yes
RoHS Compliance Yes

 


Select different version