Open topic as PDF Version 3.4

Views

Display the MA Dimmer Network using one of the three views:

• Normal View
• Dimmer View
• Log View

Requirement:

• Add MA NDPs to the network configuration

For more information see Adding devices to your session.

• Open MA Dimmer Network

For more information on how to open the MA Dimmer Network see Network dimmer. 

To toggle between the views, tap the View button in the title bar of the window MA Dimmer Network. 

Normal View

The Normal View solely displays the dimMA hierarchy. 

For more information on the dimMA hierarchy see Network dimmer. 

Dimmer View

To toggle to Dimmer View, tap Normal View in the title bar.

The Dimmer View displays both:

• dimMA hierarchy and
• Dimmer channels

Settings

No.:

The number consists of a rack, crate, module and dimmer. For example, 1:1:3:4 is to be understood as rack 1, crate 1, module 3, and dimmer 4. 

Name:

Is the name of the dimmer channel in the log files and in the configuration. 

Auto Name:

If you have changed the name of the dimmer channel in the column Name, toggling Auto Name to On takes over the original name of the dimmer channel. 

Patch1 and Patch2:

Reflect the patching of the two input slots of an NDP system. 

Profile:

Create and edit profiles – assigned to each dimmer channel – in this column. 

Assign the same profile in several dimmer channels:

1. Multi select the cells in the column.
2. Press Edit and tap a cell in the column Profile. 
3. The pop-up Select Profile opens.

4. Select a profile and tap Choose Profile.
5. Tap  in the upper right corner of the pop-up. 

The profile is now applied in several dimmer channels. 

Preheat:

Is the voltage level that is used to permanently preheat the fixtures. The value of the voltage level is displayed in percent. 

U min and U max:

Limit the range of the dimmer channels in these two columns.

Panic and Control:

The values of Panic and Control are stored in the NDP and are solely displayed in this view. 

Type:

Change the type of the dimmer channels in this column. 

1. Select the type, tap and hold a cell in the column Type.
2. The pop-up Select Type opens. 

3. Tap to select a type. 

The types are:

• 8bit: The dimmer channel is controlled in the 8bit mode containing 256 increments.
• 8bit/S: The dimmer channel is controlled in the 8bit mode and contains an additional dimmer channel that triggers the values that were changed with a set fade time. This type defines the fade time of the dimmer channel. If the additional dimmer channel is set to 100 %, the values are faded within 5 minutes. Setting a lower value on the additional channel, reduces the fade time linearly. 
• 16bit: The dimmer channel is controlled in the 16bit mode containing 65536 increments. 
• 16bit/S: The dimmer channel is controlled in the 16bit mode and contains an additional dimmer channel that triggers the values that have been changed with a set fade time. For more information on the fade time see the type 8bit/S.  

Mode:

Adjust the mode of the dimmer channel in this column.

1. To set a mode, tap and hold a cell in the column Mode.
2. The pop-up Select Mode opens. 

3. Tap to select a mode.

The modes are:

• Off: Disables any reaction toward incoming control data.
• Dim: Represents the normal dimmer mode.
• Switch: The dimmer behaves like a switch. The firing angle is 90° phase of the sinus voltage of the first sine cycle. 
• NonDim: The dimmer behaves like a switch. The firing angle is 0° phase of the sine cycle. 

Threshold:

Defines the threshold value of the input control data. Threshold influences the behavior of the dimmer channel if it is in the NonDim or the Switch mode.

No Load:

Masks error messages if the minimum base load of a dimmer is not connected to the dimmer channel. It also masks error messages if the bulb is burnt out. 

Fuse:

Masks error messages if the fuse (MCB) of the dimmer channel has blown.

Overload:

Masks error messages if an overload occurs on the dimmer channel you have selected. 

Excess DC:

Masks error messages if there is bias voltage, for example if a thyristor fails. 

Response:

Smoothes out changes in the control signal. Fixtures connected to this dimmer channel respond slower. Entries between 0 and 5 are interpolated to 0.

Log View

To toggle to Dimmer View, tap Dimmer View in the title bar. 

The Log View displays both:

• dimMA hierarchy and
• Messages along with the corresponding date

The messages may be displayed in white, yellow, or red. 

• White indicates regular messages 
• Yellow indicates warning messages
• Red indicates error messages

For more information on the display of errors see Errors. 

To change to Normal View, tap Log View in the title bar.

Select different version- latest - 3.3 3.4 3.5 3.6 3.7 3.8 3.9

  previous next

Open topic as PDF